CONTACT US

3D PRINT NOW !

Contact us

3D PRINT NOW !

Fracktal works

Material Dryer System

Introducing MDS1 All-in-One solution for your material moisture control

Request a quote

Trusted BY

Material state is a key variable for success

3D printing filaments are hygroscopic, absorbing water from the atmosphere, and therefore need drying to perform at their best. In injection molding it is common practice to dry the material filament before use and most 3D printing filament is composed of the same base resins..

Over 50% of new filaments need to be dried before printing.

In some materials, even small amounts of moisture can compromise an entire print. Our data shows, that even new filament, just opened from a sealed box, often needs to be dried for best performance.

Introducing MDS-1 Material Drye

All in one solution for your filament moisture control

Fast

The in-line design dries only the section of filament to be 3D printed, reducing the amount of work needed.

Intelligent

Smart sensors help to dry the filament to the best 3D printing condition, avoiding any damage to the filament. The in-line design also avoids multiple heat cycles.

User Friendly

A user friendly UI guides the user all the way. Exchangeable and rechargeable desiccant cartridges help to eliminate down time.

Safe

Smart sensors detect filament movement and condition and adapt the internal settings accordingly.

Ultimate Material Quality Control

I am ready to get the ultimate performance from my 3D printing filament
 
Get Filament Dryer Now
Book a Call

Fracktal works

Material Dryer System

Intelligent

Smart sensors help to dry the filament to the best 3D printing condition, avoiding any damage to the filament. The in-line design also avoids multiple heat cycles.

Versatile

Any spool format or size can be used with Drywise thanks to the in-line architecture. Drywise is available in 1.75 or 2.85mm versions

Have you experienced the following?

Effects Of moisture

  • Subpar surface finish
  • Dimensional inaccuracies
  • Poor mechanical properties
  • Inconsistent material extrusion

Hidden costs
of Moisture Damage

Valuable time is lost planning material drying, researching the correct drying parameters and handling material.

The filament needs to be optimally dried before printing. This takes many hours (even days) depending on the state of the material. This could delay scheduled production.

Full utilisation of the machinery at hand is very difficult as filament needs to be planned and dried days in advance.

Even when following standard operating procedures, different results can be expected. There are many unknowns that affect the process, initial humidity in the filament, relative humidity of the environment, rate of moisture loss in the oven, etc…

After drying, other devices are needed to keep the filament in a good state.

Multiple heat cycles, needed over the course of a spool if this is not used up immediately, eventually degrade the material quality.

Optimize Your Productivity

Save time

Smart sensors help to dry the filament to the best 3D printing condition, avoiding any damage to the filament. The in-line design also avoids multiple heat cycles.

Save Money

Smart sensors help to dry the filament to the best 3D printing condition, avoiding any damage to the filament. The in-line design also avoids multiple heat cycles.

Save Material

Smart sensors help to dry the filament to the best 3D printing condition, avoiding any damage to the filament. The in-line design also avoids multiple heat cycles.

Frequently Asked Questions

Most frequent questions and answers

A large majority of 3D printing plastics absorb moisture from the surrounding air which can significantly impact the quality of your 3D prints. These plastics are known as hygroscopic. As the filament is extruded, moisture absorbed in the plastic will rapidly expand, boil and rupture, forming bubbles in the extruded plastic. These bubbles can have a significant impact on the surface quality, layer adhesion and mechanical performance of your 3D printed parts. To avoid this, we recommend using Drywise in-line filament dryer.

3D printing plastics are prone to take in ambient moisture, which results in reduced print quality. Our dryer pre-treats the filament to best printing conditions.

I am item content. Click edit button to change this text. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus ullamcorper mattis, pulvinar dapibus leo.

We are solely an online brand, but we operate out of Malta.  

Processing for orders can take 2 to 5 days. Then EU Shipping takes 1 week. We are currently only accepting pre-orders though. We will start shipping our current orders in Q2 2022.  

 
EU Shipping Only for all Pre Orders.

We are so sorry to hear that your order arrived in less than pristine condition! Please let us make it right. Our customer service team will be more than happy to assist with processing a replacement order or issuing a refund. You may contact our customer service team by sending us an email a

Connect with Us

Information

Products

Solutions

Support

Sales & Support

Fracktal Works Call:
+91 90350 61090

Facebook Twitter Youtube

Copyright © 2023 Fracktal. All Rights Reserved.

CONTACT US